Smithco 72-000-A User Manual download pdf (Page 54)

INSTALLATION INSTRUCTIONS

You will need two people and the tailgate open with an empty hopper and the machine not operating.

1. Drill (4)

holes in front panel (Ref 7) to the left side, see drawing. Start with the top left hole at 19 inches

down from the top and 14 inches in from the left.

2. Proceed to drill the three remaining holes in a square pattern at 11 inches apart center to center. Deburr

holes and mount the hose plate (Ref 9) and secure with four (4) ¼ -20 x ¾ bolts and flange whiz lock nuts.

3. Next mount the handle holder (Ref 10) facing the front panel, at the left are a vertical row of hex bolts.

Remove the second and fourth bolts. Cut 5 inches off of the trim and put it into the top U shaped slot of

handle holder. Put the remaining piece into the bottom slot. Install boom mount bracket (Ref 12) between

hopper and handle holder. Use ¼ -20 x 2¾ bolts and flange whiz lock nuts (Ref 20). Pull boom mount

bracket outward in the slots and tighten bolts.

4. Mount the hose hanger (Ref 4) on the right hand side (Ref 6), in the upper right hand corner. Remove and

save the two bolts and nuts that are already in the upper right hand corner. Mount one hose hanger here

using the bolts and nut you just removed.

5. To mount the second hose hanger, remove the drill screw in the front upright near the plate for the door

arms is welded. Using the screw hole, drill a

hole completely through to the inside and deburr. Mount

the hanger with one ¼ - 20 x 1

bolt and flange whiz lock nut in the lower hole of the hanger. With the

hanger in the vertical position, use the remaining hole as a guide to drill a second mounting hole through

to the inside. Deburr and install the remaining bolt and nut.

6. Install latch bracket (Ref 15) using two ¼ - 20 x

machine screws and flange whiz lock nuts (Ref 14).

7. Next install boom (Ref 13) onto boom mount bracket. Hold in place with two

x 1 cotter pins (Ref 11). To

adjust, swing boom back alongside the hopper until support comes in contact with the latch bracket. Slide

latch bracket upward in the slot holes until it lifts boom

". Tighten the bolts (Ref 14).

8. Next connect the hose to the hose handle (Ref 2) with hose on the same side as the long handle and

secure with one hose clamp (Ref 1). At the other end of the hose connect the remote hose connector and

secure with the other hose clamp.

9. Bolt hose clamps (Ref 17) together over the 8" Hose, close to center. Use the

- 18 x

bolt and flange

whiz lock nut (Ref 18) on one side. Use the

- 18 x

bolt, washer and flange whiz lock nut (Ref 16) on

the other end with the washer between the bolt and the chain. The bolt must go through the end link in the

chain first then through the clamp.

10. Put the two round grips (Ref 3) on to the hose handle.

11. For storage place remote hose connector in hose plate (Ref 9) on the front panel. Drape hose over the top

and go toward the back of machine. Just past the rear hose hanger bring hose to the side of machine and

up into the hose hangers. At the front place the hose handle (Ref 2) into the handle holder (Ref 10).

12. To use the remote vacuum remove the cover plate from either side of the vacuum housing and place the

remote hose connector (Ref 8) there. Place the cover plate into the hose plate (Ref 9). Before using the

vacuum the lever on the left side of the vacuum housing must be pulled out and turned clockwise 90° and

pushed in.

13. You may want to remove the hose handle, hose and remote hose connector if you are not going to use the

remote vacuum for an extended amount of time.

1 2 ... 49 50 51 52 53 54 55 56 57 58

Comments to this Manuals

No comments

Smithco 72-000-A User Manual Page 54

Comments to this Manuals